This article mainly introduces:

Hungary hydraulic cylinder,grate cooling hydraulic cylinder manufacturer,grate cooling hydraulic cylinder

(Hungary grate cooling hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

grate cooling hydraulic cylinder are widely used in Hungary，because of no need for deceleration device，long service life，smooth movement.So our company has designed grate cooling hydraulic cylinder for customers from Hungary.

Introduction to grate cooling hydraulic cylinder:

Because of the slightly complex structure of the buffer grate cooling hydraulic cylinder, sometimes there will be problems, such as when the grate cooling hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

When the grate cooling hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the grate cooling hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the grate cooling hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the grate cooling hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair grate cooling hydraulic cylinder are not high.

When the grate cooling hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the grate cooling hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the grate cooling hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Before purchasing the grate cooling hydraulic cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

Answers to some questions about grate cooling hydraulic cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

What is the function of the hinged cylinder of the shield machine?
The articulated cylinder is used for the shield when the radius of curvature is very small during the propulsion process, that is, for turning. For example, a propulsion section with a radius of curvature of R150 can only be turned using an articulated system due to the sensitivity of the shield body (i.e. the length of the shield body divided by its outside diameter). However, in the construction process, the use of articulated systems is not much.