Release time：2023-12-12 10:13:54 Hits： Current position: Home > News
This article mainly introduces:
Kazakhstan hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder
(Kazakhstan single rack cylinder,produced by Hengyu Group）
single rack cylinder are widely used in Kazakhstan，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed single rack cylinder for customers from Kazakhstan.
The single rack cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the single rack cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The single rack cylinder is basically composed of single rack cylinder and single rack cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.
What kind of process is used in the single rack cylinder to make high-quality single rack cylinder products: the body is the main component of the single rack cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The single rack cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the single rack cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the single rack cylinder increases by 25%. If the service life of the single rack cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. single rack cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the single rack cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and single rack cylinder are stuck or the single rack cylinder is blocked. At this time, no matter how to manipulate, the single rack cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the single rack cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.
How the cavitation of the single rack cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the single rack cylinder, resulting in corrosive damage to the parts.
The single rack cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the single rack cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the single rack cylinder wall due to the stiffness and the weight of the parts, causing scars.
Does the abbreviation bc stand for bucket cylinder or boom cylinder?
Hydraulic excavator hydraulic cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder three parts, four cylinders. Because of the different naming conventions of major manufacturers, the meaning of BC is also different, for the sake of insurance, you need to consult the manufacturer.
What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.
Add Wechat