This article mainly introduces:

Ethiopia hydraulic cylinder,steering cylinder manufacturer,steering cylinder

(Ethiopia steering cylinder,produced by Hebei Hengyu company）

steering cylinder are widely used in Ethiopia，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed steering cylinder for customers from Ethiopia.

Introduction to steering cylinder:

If the steering cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the steering cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow steering cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the steering cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the steering cylinder includes the leakage caused by excessive wear of the steering cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and steering cylinder, and the phenomenon of "pulling the steering cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

The assembly work of the steering cylinder has a great impact on the quality of the steering cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The material of the sliding part of the steering cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

The piston rod and guide sleeve function of the steering cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

Answers to some questions about steering cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

Need to buy a hydraulic cylinder, now only know that the pressure needs to be between 20t and 50t. Two-way travel, how to determine the type of cylinder?
Important parameters of the cylinder: cylinder diameter, stroke, use pressure. First, the system pressure must be determined according to the precision of the operation of the application equipment, and the cylinder diameter can be determined by the force and system pressure. Then, according to how the equipment and the cylinder are installed and connected, determine the installation method of the cylinder and then determine the specific installation size, the size of the oil port, whether the buffer is needed and other details.