This article mainly introduces:
Turkey hydraulic cylinder,swager cylinder manufacturer,swager cylinder
(Turkey swager cylinder,produced by Hengyu Hydraulic Cylinder Factory）
swager cylinder are widely used in Turkey，because of long service life，high work efficiency，no transmission clearance.So our company has designed swager cylinder for customers from Turkey.
When the swager cylinder is installed, the piston and the swager cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the swager cylinder head boss is easy to cause scars when it hits the inner surface of the swager cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized swager cylinders, only careful and careful operation can be avoided.
When the initial action of the swager cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the swager cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.
The piston rod and guide sleeve function of the swager cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.
If the swager cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the swager cylinder. The internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the swager cylinder bore processing is out of whack. Because the piston and swager cylinder, guide rail and piston rod are relative If the swager cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling swager cylinder weight composition and calculation. The weight of the swager cylinder is composed of the swager cylinder diameter, the outer diameter and weight of the swager cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.
Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.
How to choose cylinder size, pump type, motor power for a 30-ton press?
30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.
Add Wechat