This article mainly introduces:

Saudi Arabia hydraulic cylinder,plunger type cylinder manufacturer,plunger type cylinder

(Saudi Arabia plunger type cylinder,produced by Hebei Hengyu company）

plunger type cylinder are widely used in Saudi Arabia，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed plunger type cylinder for customers from Saudi Arabia.

Introduction to plunger type cylinder:

The daily inspection of the plunger type cylinder includes: checking the connection of the plunger type cylinder and the pipe joint for leaks. Check the plunger type cylinder rod for leaks. Check the plunger type cylinder connection for leaks. When the plunger type cylinder moves, the work is normal and smooth. Whether the plunger type cylinder has internal leakage.

plunger type cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

plunger type cylinder piston rod material introduction: In general, we use 45 steel to produce plunger type cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

When the plunger type cylinder needs to be stored for a period of time, please follow the recommended methods: The plunger type cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the plunger type cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil plunger type cylinder should not be in direct contact with water vapor for a long time. The plunger type cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the plunger type cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the plunger type cylinder Before working, the plunger type cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the plunger type cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about plunger type cylinder:

What do cylinder internal leakage and external leakage mean?
Internal leakage means that the piston seal in the cylinder is not strict, there is a leak between the two chambers of the cylinder, the oil is still in the cylinder, and the external leakage is that the oil leaks to the outside of the cylinder.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.