This article mainly introduces:

Croatia hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

(Croatia rolling mill cylinder,produced by Hengyu Hydraulic Co., Ltd）

rolling mill cylinder are widely used in Croatia，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed rolling mill cylinder for customers from Croatia.

Introduction to rolling mill cylinder:

The repair method of rolling mill cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

In the case of serious wear on the inner surface of the rolling mill cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the rolling mill cylinder manufacturing process for replacement. The rolling mill cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The role of the rolling mill cylinder in the mold industry: the rolling mill cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the rolling mill cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The rolling mill cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

The assembly work of the rolling mill cylinder has a great impact on the quality of the rolling mill cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about rolling mill cylinder:

How to select the 2.5T bearing cylinder and hydraulic pump?
2,5 ton load is not heavy, you can use the rated pressure of 16 mpa gear pump, neither waste nor save cost, load/pressure = cylinder diameter, preset pressure of 8 mpa, 2500 (kg) /80 (bar) =31.25 square centimeters, in the open =63 mm, cylinder diameter can be selected 63 mm, stroke according to the situation, Hydraulic pump select gear pump, if there is a speed requirement, in order to calculate the displacement, the motor power also needs to determine the displacement of the pump to calculate.

How many boom cylinders, bucket rod cylinders and bucket cylinders are there in a small single-bucket excavator?
one for bucket, one for forearm, only one piece for a small excavator under the big arm, two pieces for medium and large excavator.