This article mainly introduces:

Hungary hydraulic cylinder,trailer hydraulic cylinder manufacturer,trailer hydraulic cylinder

(Hungary trailer hydraulic cylinder,produced by Hengyu Group）

trailer hydraulic cylinder are widely used in Hungary，because of high work efficiency，long service life，smooth movement.So our company has designed trailer hydraulic cylinder for customers from Hungary.

Introduction to trailer hydraulic cylinder:

What kind of process is used in the trailer hydraulic cylinder to make high-quality trailer hydraulic cylinder products: the body is the main component of the trailer hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The trailer hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the trailer hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the trailer hydraulic cylinder increases by 25%. If the service life of the trailer hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. trailer hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the trailer hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and trailer hydraulic cylinder are stuck or the trailer hydraulic cylinder is blocked. At this time, no matter how to manipulate, the trailer hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the trailer hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

trailer hydraulic cylinder use should try to avoid sealing belt into the trailer hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the trailer hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the trailer hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The trailer hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the trailer hydraulic cylinder, bite. Elimination method: When installing the trailer hydraulic cylinder, ensure that the axis position of the trailer hydraulic cylinder is consistent with the direction of movement; Make the load borne by the trailer hydraulic cylinder as far as possible through the trailer hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

In the process of using the trailer hydraulic cylinder, sometimes such a problem will occur, the trailer hydraulic cylinder can not act immediately after the instruction of the trailer hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil trailer hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about trailer hydraulic cylinder:

Do the collecting cylinder, distributing cylinder and distributing cylinder on the organic heat carrier boiler need to be notified separately as the pressure vessel for construction?
Do not need to be installed as a separate pressure vessel to inform, according to the organic heat carrier boiler can be informed. Write a "special equipment installation, renovation and maintenance notice" issued on it.

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.