This article mainly introduces:

Sri Lanka hydraulic cylinder,hydraulic jack cylinder manufacturer,hydraulic jack cylinder

(Sri Lanka hydraulic jack cylinder,produced by Hebei Hengyu company）

hydraulic jack cylinder are widely used in Sri Lanka，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed hydraulic jack cylinder for customers from Sri Lanka.

Introduction to hydraulic jack cylinder:

The assembly work of the hydraulic jack cylinder has a great impact on the quality of the hydraulic jack cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the hydraulic jack cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Under normal circumstances, the hydraulic jack cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the hydraulic jack cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the hydraulic jack cylinder and the end cover, the piston and the piston rod, the piston and the hydraulic jack cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the hydraulic jack cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

When using the hydraulic jack cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the hydraulic jack cylinder block. If the hydraulic jack cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the hydraulic jack cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the hydraulic jack cylinder, so that the working efficiency of the hydraulic jack cylinder is reduced.

Answers to some questions about hydraulic jack cylinder:

How to calculate cylinder speed?
If there is a throttle valve, the cylinder speed will be adjustable. When the throttle is fully opened, the speed of the cylinder reaches the maximum: maximum speed = oil pump displacement ÷ cylinder cavity cross-sectional area The displacement of the oil pump is a main indicator, which can be found on the nameplate, and some can also be known by the oil pump model; The cross-sectional area of the cylinder cavity can be easily calculated. Just make sure the units are the same. And because the cross-sectional area of the rod cavity and the rodless cavity of the cylinder is different, the speed of advance and retreat may also be different.

How to distinguish cylinder rod head and cylinder bottom?
One end of the piston rod can be telescopic is the rod head, and the one behind is the bottom of the cylinder, which is the single rod cylinder.