This article mainly introduces:

Paraguay hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Paraguay tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tilting furnace hydraulic cylinder are widely used in Paraguay，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed tilting furnace hydraulic cylinder for customers from Paraguay.

Introduction to tilting furnace hydraulic cylinder:

When the tilting furnace hydraulic cylinder is in use, ensure that the tilting furnace hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Improve the service life of the tilting furnace hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the tilting furnace hydraulic cylinder (such as the tilting furnace hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the tilting furnace hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the tilting furnace hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single tilting furnace hydraulic cylinder exhaust.

The tilting furnace hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the tilting furnace hydraulic cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The tilting furnace hydraulic cylinder is basically composed of tilting furnace hydraulic cylinder and tilting furnace hydraulic cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

The tilting furnace hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the tilting furnace hydraulic cylinder, bite. Elimination method: When installing the tilting furnace hydraulic cylinder, ensure that the axis position of the tilting furnace hydraulic cylinder is consistent with the direction of movement; Make the load borne by the tilting furnace hydraulic cylinder as far as possible through the tilting furnace hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

Answers to some questions about tilting furnace hydraulic cylinder:

How long can a hydraulic cylinder work continuously?
If the maintenance is good, the service life can be extended a lot. The life of the cylinder is related to the structure of the cylinder, working pressure, stress state, hydraulic oil cleanliness, oil temperature control, maintenance and preventive measures. For example, the cylinder structure, the inner wall of the cylinder has quilting, rolling, chrome plating and other methods, the sealing parts have polyurethane rings, glay rings, metal sealing rings, etc., different combinations, the life difference is dozens of times. Metallurgical system is a typical cylinder application, in 24 hours of work, a year or more can not be shut down, in the middle of continuous work.

Why does the hydraulic cylinder not return?
For a spring return cylinder, it is possible that 1, the spring is damaged. You can check it for processing. 2, the oil in the oil path is not unloaded, causing it to be unable to reset. 3, the cylinder piston is dead, resulting in no position. For double-acting cylinders, it is possible to: 1, the spool is not reversed, or is not changed to the correct position, check whether the reversing valve is normal (and whether there is electricity). 2, the cylinder piston is dead, resulting in no position, check and treatment can be. 3, the return oil pressure is insufficient, the inlet oil is not unloaded, the operation is not smooth. For reference only.