This article mainly introduces:

Saudi Arabia hydraulic cylinder,pipe bender hydraulic cylinder manufacturer,pipe bender hydraulic cylinder

(Saudi Arabia pipe bender hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

pipe bender hydraulic cylinder are widely used in Saudi Arabia，because of no transmission clearance，simple structure and reliable operation，excellent temperature resistance.So our company has designed pipe bender hydraulic cylinder for customers from Saudi Arabia.

Introduction to pipe bender hydraulic cylinder:

The repair method of pipe bender hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

There are some honeycomb holes in the inner wall of the pipe bender hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the pipe bender hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the pipe bender hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the pipe bender hydraulic cylinder is targeted to prevent. Is very necessary.

The "O" ring can be used as an auxiliary seal inside the pipe bender hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the pipe bender hydraulic cylinder, and can be completely sealed.

Repair method of small range wear of oil pipe bender hydraulic cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

Answers to some questions about pipe bender hydraulic cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.