This article mainly introduces:

India hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

(India servo hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

servo hydraulic cylinder are widely used in India，because of no need for deceleration device，long service life，smooth movement.So our company has designed servo hydraulic cylinder for customers from India.

Introduction to servo hydraulic cylinder:

If the servo hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the servo hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow servo hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the servo hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the servo hydraulic cylinder includes the leakage caused by excessive wear of the servo hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and servo hydraulic cylinder, and the phenomenon of "pulling the servo hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

The method of sleeve servo hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the servo hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the servo hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

servo hydraulic cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

When purchasing the servo hydraulic cylinder, try to clarify the following parameters of the servo hydraulic cylinder: A. servo hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or servo hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right servo hydraulic cylinder type can be found accurately and quickly.

Answers to some questions about servo hydraulic cylinder:

About the hydraulic cylinder wall thickness problem?
Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.

Hydraulic cylinder performance requirements?
Hydraulic cylinder performance requirements: hydraulic cylinder is the hydraulic system to achieve energy transfer, conversion and control of the working medium, in addition, it is also responsible for the lubrication of the system, rust prevention, corrosion prevention and cooling. The performance of hydraulic oil will make the system flexible, accurate and reliable. Hydraulic performance requirements are determined according to the design parameters of the hydraulic system, operating conditions, the structure of the hydraulic pump and the working environment. Appropriate viscosity and good viscosion-temperature performance Viscosity is an important performance indicator of hydraulic pressure, which has an important impact on the smooth operation of the hydraulic system and the friction parts. The low temperature performance of hydraulic oil includes three aspects: low temperature flow, low temperature start-up and low temperature pumping.