This article mainly introduces:

S.Africa hydraulic cylinder,swager cylinder manufacturer,swager cylinder

(S.Africa swager cylinder,produced by Hengyu Hydraulic Co., Ltd）

swager cylinder are widely used in S.Africa，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed swager cylinder for customers from S.Africa.

Introduction to swager cylinder:

swager cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the swager cylinder is placed for a period of time, the swager cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

swager cylinder piston rod material introduction: In general, we use 45 steel to produce swager cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

In order to ensure the service life of the swager cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the swager cylinder, causing damage to the seal and causing leakage in the swager cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

swager cylinders in series, parallel and series parallel. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the swager cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the swager cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about swager cylinder:

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.