This article mainly introduces:

Canada hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

(Canada synchronous hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

synchronous hydraulic cylinder are widely used in Canada，because of no need for deceleration device，long service life，smooth movement.So our company has designed synchronous hydraulic cylinder for customers from Canada.

Introduction to synchronous hydraulic cylinder:

synchronous hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the synchronous hydraulic cylinder head itself is the guide sleeve of the piston rod, the synchronous hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the synchronous hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

The "O" ring can be used as an auxiliary seal inside the synchronous hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the synchronous hydraulic cylinder, and can be completely sealed.

synchronous hydraulic cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a synchronous hydraulic cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' synchronous hydraulic cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the synchronous hydraulic cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The synchronous hydraulic cylinder mainly outputs linear motion and force. The synchronous hydraulic cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston synchronous hydraulic cylinder, plunger synchronous hydraulic cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger synchronous hydraulic cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The synchronous hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the synchronous hydraulic cylinder, bite. Elimination method: When installing the synchronous hydraulic cylinder, ensure that the axis position of the synchronous hydraulic cylinder is consistent with the direction of movement; Make the load borne by the synchronous hydraulic cylinder as far as possible through the synchronous hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

Answers to some questions about synchronous hydraulic cylinder:

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.