This article mainly introduces:

Bahrain hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

(Bahrain 200 ton hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

200 ton hydraulic cylinder are widely used in Bahrain，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed 200 ton hydraulic cylinder for customers from Bahrain.

Introduction to 200 ton hydraulic cylinder:

200 ton hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the 200 ton hydraulic cylinder head itself is the guide sleeve of the piston rod, the 200 ton hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the 200 ton hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

The 200 ton hydraulic cylinder is mainly composed of body, piston, piston rod, 200 ton hydraulic cylinder head, 200 ton hydraulic cylinder bottom, piston rod head and related auxiliary devices. The piston divides the 200 ton hydraulic cylinder into two chambers, and moves reciprocally in the 200 ton hydraulic cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the 200 ton hydraulic cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the 200 ton hydraulic cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the 200 ton hydraulic cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the 200 ton hydraulic cylinder bottom and the 200 ton hydraulic cylinder head is serious, so the buffer deceleration should be set at both ends of the 200 ton hydraulic cylinder The working medium of the 200 ton hydraulic cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; 200 ton hydraulic cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the 200 ton hydraulic cylinder: The buffer structure of the 200 ton hydraulic cylinder is to prevent the piston from colliding with the 200 ton hydraulic cylinder head at the end of the stroke.

After the 200 ton hydraulic cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

When the 200 ton hydraulic cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the 200 ton hydraulic cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

Answers to some questions about 200 ton hydraulic cylinder:

How big gear pump need to use for 60*100 cylinder?
One cylinder size alone does not determine the size of the pump used. Choose the size of the pump, at least to know 1, the size of the load is how much, by the size of the load and the size of the cylinder and other conditions can be calculated the pressure required by the hydraulic system. 2. Speed of operation. From this speed and cylinder size, the required flow rate of the system is calculated. The relevant parameters of the pump can be selected by the pressure and flow rate to determine what kind of pump is required.

What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.