This article mainly introduces:

Uzbekistan hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

(Uzbekistan tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

tailplate hydraulic cylinder are widely used in Uzbekistan，because of long service life，smooth movement，high work efficiency.So our company has designed tailplate hydraulic cylinder for customers from Uzbekistan.

Introduction to tailplate hydraulic cylinder:

The body of the tailplate hydraulic cylinder on the processing process requirements: the body of the tailplate hydraulic cylinder is an important and essential part of the tailplate hydraulic cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the tailplate hydraulic cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

When the tailplate hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The tailplate hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tailplate hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tailplate hydraulic cylinder should not be in direct contact with water vapor for a long time. The tailplate hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tailplate hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tailplate hydraulic cylinder Before working, the tailplate hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tailplate hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

When the tailplate hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the tailplate hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil tailplate hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical tailplate hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the tailplate hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

When using the tailplate hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the tailplate hydraulic cylinder block. If the tailplate hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the tailplate hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the tailplate hydraulic cylinder, so that the working efficiency of the tailplate hydraulic cylinder is reduced.

Answers to some questions about tailplate hydraulic cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

How does the one-way solenoid valve control the hydraulic cylinder circuit?
If your cylinder is single-acting, you can use a one-way solenoid valve, such as some lifting platform hydraulic cylinder, the support valve used is one-way (two-position tee), that is, the cylinder extends out by the oil pressure top, the cylinder retracted by its own weight.